Monitoring Printers Without Losing Your Soul
Every trade has a running joke, and ours is the printer. The copier that jams when the finance director walks past. The driver that installs in a language nobody chose. The machine that senses fear. If you have worked a help desk for more than a week you have a printer story, and it is probably a good one. This guide is not going to pretend otherwise.
The joke is also the argument for monitoring. A device that fails often and in front of everyone is exactly the device you want to hear about first. And printers get left out of monitoring precisely because they are the joke. Somewhere in your building there is a printer whose output is not optional: payroll checks, shipping labels, prescriptions, invoices, pick lists, patient wristbands. Printing is usually the last physical step of a digital process, and when that step stops, the process stops. I learned this on a payroll day, and I have not left a payroll printer unmonitored since.
By the end of this guide you will know what a network printer can report about itself. You will know why a ping check on its own is not enough. And you will know exactly which checks to set up for every printer you care about. None of it needs special tools beyond ordinary network monitoring.
In this guide
- Why printers deserve real monitoring
- What a printer will tell you over the network
- Why ping alone lies to you
- The starter monitoring set for every printer
- Deciding which printers get the full treatment
- Know your fleet: printers and inventory
- The printer that outlives three servers
- Where to go next
Why printers deserve real monitoring (yes, printers)
Think about what your organization actually prints. Not the meeting agendas — the documents where a delay has a dollar value or a compliance value. A warehouse that cannot print shipping labels is a warehouse that cannot ship. A clinic that cannot print prescriptions or wristbands has a patient-safety problem, not an IT ticket. A finance team that cannot print checks on payroll day has a very specific kind of emergency. In each case the "printer problem" is really a business-process outage wearing a beige plastic disguise.
Now weigh the two sides of the scale. Adding a printer to your monitoring system costs a few minutes of setup. It also costs a trickle of network traffic so small the printer will not notice. Not monitoring it costs you the worst kind of discovery. You find out from an angry human, at the exact moment the output was needed, that the device has been dead since the weekend. Monitoring does not make printers reliable, but it converts surprises into notifications, and notifications arrive before the crowd does.
Printer failures are also among the most user-visible failures in IT. Users forgive a slow database query they never see; they remember standing at a silent printer while their meeting starts without them. When your monitoring lets you say "yes, we know, a fix is already moving" before the second complaint lands, you are not just fixing a printer. You are maintaining the general belief that IT knows what is happening — which is a resource you draw on every time something bigger breaks.
So the goal of this pillar is not to defend printers. They are guilty. The goal is to stop being surprised by them.
What a printer will tell you over the network
The pleasant surprise of printer monitoring is how chatty printers are. Nearly every business network printer speaks SNMP (Simple Network Management Protocol). This is the standard question-and-answer protocol monitoring tools use to ask devices about their internals. Better still, printers largely agree on which questions they will answer, because there is a standard Printer MIB. A MIB, or Management Information Base, is the published dictionary of questions a device type supports. Vendors add their own extras on top, but the standard set is enough for real monitoring, and it works across brands. Here is what lives in it, in plain terms:
- Device and printer status. Is the printer up, idle, actively printing, or warming up? And is the overall device running normally, running with a warning, or down? This is the printer's own answer, not a guess from outside.
- Detected error conditions. A compact set of yes/no flags for the classics: paper low, paper out, toner low, toner out, door open, paper jammed, offline, service requested. This is the closest thing to reading the little screen on the printer without walking to it.
- Supply levels. There is a table of every consumable the printer tracks — toner or ink cartridges, drums, fusers, waste containers. Each has a description, a current level, and a maximum, so you can compute a percentage. Some models report exact numbers, some only report coarse steps, and a few will only admit "something remains." Honest monitoring works with all three.
- Input tray states. Which trays exist, what they hold, and whether they are empty — useful when "the printer is broken" actually means "tray 2 has been empty since Tuesday."
- Page counts. A lifetime engine counter, like a car's odometer. It only ever goes up. It quietly answers questions thresholds cannot. These include which printers do the real work and which are idle enough to retire. It also tells you whether that "low-volume" device is secretly printing half the building's output.
- Identity. Model, description, and usually the serial number — inventory gold, because it means your monitoring system can also keep your printer list truthful.
Two footnotes on scope. Vendors extend this standard set with their own private additions — more precise supply data, temperature readings, and so on. Your monitoring tool may know how to use them. But you do not need them to get started. The standard set above is the reliable common ground across brands. And if your fleet is mostly MFPs (multifunction printers — the big copier-scanner-printer combos), there is good news. The printing side of an MFP answers these same standard questions. So everything in this guide applies. The scanning and copying sides are murkier, and we deal with them in the peripheral zoo guide.
If you have a command-line SNMP toolkit handy, you can see all of this yourself. Ask a printer for its status and its supply descriptions and it will answer with something like:
# Is the printer idle, printing, or warming up? snmpget -v2c -c printread 10.0.40.31 1.3.6.1.2.1.25.3.5.1.1.1 HOST-RESOURCES-MIB::hrPrinterStatus.1 = INTEGER: idle(3) # What consumables does it track? snmpwalk -v2c -c printread 10.0.40.31 1.3.6.1.2.1.43.11.1.1.6 Printer-MIB::prtMarkerSuppliesDescription.1.1 = STRING: Black Toner Cartridge Printer-MIB::prtMarkerSuppliesDescription.1.2 = STRING: Imaging Drum Unit
The long dotted numbers are OIDs (Object Identifiers) — think of them as drawer numbers in a giant standardized filing cabinet of device facts. You rarely type them by hand in practice. A monitoring tool that understands printers asks for all of this automatically once it recognizes the device. The point of seeing it raw once is to demystify it: printer monitoring is not exotic. It is ordinary SNMP against a device that happens to hold paper.
Tip: printers often ship with SNMP enabled and the default read community string of public. This means anyone on the network can query them. On some models defaults also allow changing settings. While you are setting up monitoring, do the five-minute hardening pass. Set a non-default read-only community string (or SNMPv3 where supported). Disable write access unless you need it, and restrict queries to your monitoring server's address. You get better monitoring and a smaller attack surface in the same visit to the admin page.
Why ping alone lies to you
The instinctive first step is to add a ping check to each printer and call it done. Ping — the tiny "are you there?" message any networked device answers if it is alive — is genuinely useful and you should absolutely have it. But understand what it proves: the printer's network card is powered and reachable. That is all. A printer with a paper jam pings perfectly. A printer with an empty toner cartridge pings perfectly. A printer displaying a cryptic error and refusing all jobs pings perfectly.
Real printer availability has three layers, and each layer catches failures the one below cannot see. The second layer is a TCP port check: opening a connection to the port where print jobs actually arrive and confirming something answers. Most network printers accept raw print jobs on port 9100. Many also speak IPP (Internet Printing Protocol) on 631. Some older models still offer LPD (the venerable Line Printer Daemon protocol) on 515. A port check answers a better question than ping: not "is the box on?" but "is the door where jobs go actually open?" Printers whose print engine has hung sometimes keep answering pings while that door stays shut.
The third layer is the SNMP status check you met above: ask the printer how it feels, and alert on the answer. This is the layer that catches the jam, the open door, the offline toggle, and the supply outage. This covers every state where the printer is reachable, listening, and not printing. Stack the three and you can finally distinguish "network problem," "device hung," and "device is up but crying for help." As you will see in the troubleshooting playbook, that is most of printer triage done before you leave your chair.
At Northgate Retail the dispatch label printer had one check on it, a ping, and the ping was green all morning. The printer had tripped its jam sensor during the night shift and its front panel said so, to an empty warehouse. Dispatch found out at ten, when the first courier arrived for pallets that had no labels. The queue behind the jam held four hours of pick lists. The monitoring review recorded that the ping check "had performed as configured". It had. That was the problem.
| Layer | The question it answers | A failure here typically means |
|---|---|---|
| Ping | Is the device powered and reachable? | Power, cable, switch port, or address problem — a network issue, not a printer issue |
| TCP port (9100 / 631 / 515) | Is the print service accepting jobs? | Print engine or controller hung; device may need a restart even though it pings |
| SNMP status + error flags | What does the printer say is wrong? | Jam, door open, out of paper or toner, offline, service requested — a human visit with the right part |
The starter monitoring set for every printer
Here is a starter set that covers the failures people actually experience, without burying you in noise. It is deliberately modest — you can enrich it later, and the other guides in this pillar go deeper on supplies and queues. For each printer you decide to monitor:
| # | Check | How | Frequency | Starting alert rule |
|---|---|---|---|---|
| 1 | Reachability | Ping | 1–5 min | Down for 10 minutes |
| 2 | Print service | TCP connect to 9100 (or 631) | 5 min | Port closed while ping still succeeds |
| 3 | Printer status | SNMP status + error flags | 5–10 min | Jam, door open, offline, or service-requested persisting 15 minutes |
| 4 | Supply levels | SNMP supply table | A few times a day | Below your reorder threshold (see the consumables guide) |
| 5 | Page count | SNMP lifetime counter | Daily | No alert — record it for trends and inventory |
| 6 | Queue depth | Print server, where one exists | 5–15 min | Oldest queued job older than 30 minutes in business hours |
Three notes on tuning. First, notice the timers are gentle. A printer that drops off the network for ninety seconds and comes back is a non-event. Requiring a failure to persist before alerting means ten minutes down, fifteen minutes in an error state. That filters out self-clearing blips while still catching everything a human would care about.
Second, decide the severity of each condition honestly. "Paper out" on a busy shared printer will happen every few days forever. That is a heads-up at most, or simply a dashboard color, not a page. A jam that has persisted through lunch, on the other hand, means everyone who tried to print has silently given up or is queuing jobs into the void. That deserves a ticket. Reserve anything resembling urgency for the small set of printers whose output is business-critical, and let the rest be quietly visible instead of loud.
Third, printing is a business-hours activity almost everywhere. An alert about a jammed lobby printer at 2 AM helps no one and erodes trust in every future alert. Route printer alerts into a business-hours window by default. Make exceptions only for the printers that genuinely work night shift — the warehouse label printer, the pharmacy, the plant floor.
Deciding which printers get the full treatment
Monitor all printers at layer one and two. Ping and port checks are nearly free, and even a humble huddle-room printer deserves a dashboard dot. Then promote a shortlist to the full starter set. The test for promotion is a single question: if this printer stopped at the worst plausible moment, would someone outside IT escalate within the hour? The payroll printer, the shipping-label printers, the front-desk device that prints visitor badges, anything in a clinical or legal workflow — these are your critical tier. They get status checks, supply thresholds, and alerting with teeth.
Writing the tier down matters more than it seems. When a critical-tier printer alerts, whoever is on duty should already know it is critical — not discover it by the volume of the complaints. A one-line note on the device in your monitoring tool ("prints payroll checks; treat as priority during month-end") converts tribal knowledge into something the newest tech can act on.
Know your fleet: printers and inventory
You cannot monitor a printer you do not know exists, and unknown printers are a genuinely common species. Departments buy them with a credit card, plug them into the wall jack, and mention it to IT never. The fix is discovery. Scan your network ranges periodically and let the printers identify themselves. They will do so over SNMP, complete with model and serial number. Any decent monitoring tool can run this sweep on a schedule and flag new arrivals. The broader discipline of turning scans into a trustworthy device list is its own topic, covered in building a device inventory. Printers are simply one of its most rewarding customers.
For each printer, your inventory wants a small, boring, priceless set of facts. Record model, serial, network address, physical location, the tier you assigned it, and who to contact about it. Add the page count your monitoring collects daily and the list stops being static paperwork. You can now see which devices carry the load. You can catch the "low-volume" printer that somehow prints a quarter of the building's pages. And you can walk into replacement or lease conversations holding real numbers instead of guesses.
Here is one address-related habit while you are in there. Give monitored printers stable addresses via DHCP reservations rather than hand-typed static settings, and record them. A printer that silently picks up a new address after a power outage is a printer your monitoring has lost and your users' drivers cannot find.
The strange dignity of the printer that outlives three servers
Once your monitoring has run for a while, it will start telling you something faintly embarrassing. Somewhere in your fleet is an ancient workgroup laser — beige gone slightly yellow, installed by a predecessor you never met. Its uptime and availability graphs beat some of your servers. It has survived two office reorganizations and three generations of the hardware it prints for. Its page count reads like a mileage badge. It jams. It also comes back, every time.
There is a real lesson hiding in the joke. Long-lived devices accumulate assumptions. There is the static address nobody documented. There is the driver that only lives on one aging file share. And there is the department that quietly depends on tray 3 being legal-size. Monitoring and inventory are how those assumptions get written down before the day the old machine finally does not come back. Respect your elders; document them.
And let the data complicate your instincts in both directions. The printer everyone jokes about may earn decent marks on paper. Meanwhile the sleek new multifunction device racks up more error-state hours than the entire rest of the fleet. Monitoring will not settle who is right about printers. It will settle what is actually happening.
Where to go next
Printers will stay the joke, and monitoring does not change that. It changes who finds out first. Layered availability checks, because ping alone lies. SNMP status and error flags, because the printer will say what is wrong if asked. Supplies and page counts, because the slow problems are the preventable ones. A critical tier, so the payroll printer never has to introduce itself through a crowd. Go deep next on the two subsystems that raise the most tickets, toner and consumables alerting and print queues and spoolers. Keep the troubleshooting playbook within reach for the day the alert fires. None of it costs you your soul. A small piece, perhaps, and you can monitor that too. The rest of the pillar lives at Printers & Peripherals on the Network.
Put this into practice with SysPeep Monitor
Printers announce themselves over SNMP — the trick is having something listening. SysPeep Monitor auto-discovers the printers on your network. It collects their status, error flags, and supply levels over SNMP alongside the rest of your infrastructure. It puts the whole fleet on one dashboard with alert rules designed to stay quiet until it matters. The free trial installs on any Windows machine in minutes.
Download Free TrialLearn About SysPeep